Qualified Scsi Hba Cards Pro Tools Systems For Mac
Search among more than 1.000.000 user manuals and view them online in.pdf. Pro Tools 10.2 and Pro Tools HD 10.2 on Mac OS X 10.6.x (“Snow Leopard”) and 10.7.x (“Lion”) — 5/8/12 4 Clovertown Mac Pro computers do not have the PCIe bandwidth required to use more than two 4x PCIe cards at full speed.
So I found a load of old Zip and SyQuest cartridges up in the attic, along with the SCSI drives for them. No idea what's on them, but could be some lost photos of my kids (a backup went screwy about 8 years ago). I have a 2008 Mac Pro, and also - somewhere in the attic - a Quad G5.
Does anyone know the best (ie. Most cost-effective) way to see what's on the drives? The SyQuest is a SyJet 1.5Gb, with SCSI in and out ports, while the Zip drive is a Zip 100 (ditto). Time has mercifully blanked out all memories of having to deal with SCSI stuff (does it need special drivers?), so if anyone can help fill in the blanks. So I found a load of old Zip and SyQuest cartridges up in the attic, along with the SCSI drives for them.
No idea what's on them, but could be some lost photos of my kids (a backup went screwy about 8 years ago). I have a 2008 Mac Pro, and also - somewhere in the attic - a Quad G5. Does anyone know the best (ie. Most cost-effective) way to see what's on the drives? If you have a bunch of SCSI drives and a G5, have you looked in the G5 to see if there's a SCSI card in it? USB Zip drives existed too, so that may be a less expensive solution for those. At that price, the OP may be better off finding a cheap ancient Mac with an onboard SCSI port (not sure how far back you'd need to go.
Here is where you configure the video and audio setting for. Wintv hvr 2250 drivers for mac.
Early PPC era, I think?) at a resale shop or what not; just something functional enough to boot, interact with the media, and then copy it off via the network. Bonus Extra FunTime™: You'll get to use Classic MacOS! The transition from ADB/SCSI to USB/Firewire was in the G3 era.
I think some of the beige G3 boxes with SCSI could run at least the first couple of versions of OS X. AppleLSIFusionSCSI IONameMatch LSILogic,scsi pci1000,30 Find a SCSI card matching that and it should work out of the box. (Possibly requiring some cable adapters to connect your devices.) Thanks - a bit over my head, but would this work?: LSI Logic LSI22320-HP Dual Channel Ultra320 SCSI HBA Card PCI-X Probably.
For that price it's worth a shot; if it has a slightly different PCI device ID, it can probably be made to work by adding its PCI ID to the plist, as that looks to have the right SCSI controller chip. I wouldn't expect that PCI-X card to work in a Mac Pro. The G5 might work, I don't have a ton of experience expanding them.
Qualified Scsi Hba Cards Pro Tools Systems For Mac
Oh, I thought the older Mac Pros had PCI-X slots, but apparently they were PCIe all the way. Apparently the switch to PCIe was made with the very last (late 2005) G5. So yeah, the PCI-X card would only be good for a G3, G4, G5 or a Hackintosh with 64-bit PCI slots (PCI-X is just a faster version; cards may even work in standard 32-bit PCI slots). There are apparently PCI-express versions of the LSI U320 SCSI cards, the 20320IE and 22320SE, so look for one of those for use with your Mac Pro (avoid -R models, which are RAID, and probably won't work with the same driver). And yes, there were both USB 1.1 and USB 2.0 ZIP drives, and the USB 1.1 ones were quite slow.
The later ones (perhaps all USB 2.0?) were bus-powered, which was nice. Just avoid the ZIP-750, which can't read the 100MB disks. The 250 is fine reading 100s, but is very slow writing to them (and writing ZIP-100s with a 250 drive is not recommended for long-term reliability, but that shouldn't matter here). I wouldn't expect that PCI-X card to work in a Mac Pro. The G5 might work, I don't have a ton of experience expanding them. Oh, I thought the older Mac Pros had PCI-X slots, but apparently they were PCIe all the way. Apparently the switch to PCIe was made with the very last (late 2005) G5.
So yeah, the PCI-X card would only be good for a G3, G4, G5 or a Hackintosh with 64-bit PCI slots (PCI-X is just a faster version; cards may even work in standard 32-bit PCI slots). There are apparently PCI-express versions of the LSI U320 SCSI cards, the 20320IE and 22320SE, so look for one of those for use with your Mac Pro (avoid -R models, which are RAID, and probably won't work with the same driver). And yes, there were both USB 1.1 and USB 2.0 ZIP drives, and the USB 1.1 ones were quite slow. The later ones (perhaps all USB 2.0?) were bus-powered, which was nice. Just avoid the ZIP-750, which can't read the 100MB disks. The 250 is fine reading 100s, but is very slow writing to them (and writing ZIP-100s with a 250 drive is not recommended for long-term reliability, but that shouldn't matter here).
Thanks so much, everyone - I can see that I was completely out of my depth on this one. Would this board work?: LSI LSI20320IE PCI Express Ulta320 SCSI Single-Channel Host Bus Adapter (HBA) Thanks again.
Qualified SCSI HBA Cards Pro Tools Systems for Windows XP Qualified SCSI HBA Cards Pro Tools Systems for Windows XP For maximum track count, use of a qualified SCSI HBA (Host Bus Adapter) card is required with Pro Tools HD systems. Pro Tools 6.x & 7.x The following card is officially qualified with Pro Tools 6.x & 7.x systems on Windows XP. Included With the Digidesign SCSI 128 Kit or Available as a Separate Purchase: ATTO EPCI-UL3D.
Supports up to 192 tracks of playback and record with Pro Tools HD Accel Systems. ATTO UL3D BIOS version 1.68 or higher required for the Digidesign SCSI 128/ATTO UL3D.
For more information, see the following:. (51 k). This document, as well as the ATTO Utilities folder, is on the Pro Tools 6.9.x/7.x CDs. Also available from the Digidesign. The ATTO Utilities folder from the Pro Tools 6.9.x/7.x CDs is also available from the. Before upgrading ATTO driver and firmware, disconnect all drives attached to the ATTO SCSI controller card. Sync Rate set to '160DT (80)' (160 MB/sec at 80 MHz).
PCI Burst Rate set to 128. Selection Timeout: 16ms.Settings available via SCSI BIOS Note: The 66MHz version of the ATTO EPCI-UL3D (model # EPCI-UL3D-066) is not supported for use with Pro Tools systems, regardless of whether your Pro Tools system is installed on a 33 MHz or 66 MHz PCI bus. The 66 MHz version is tuned for performance on a 66 MHz PCI bus. However, when Pro Tools is installed in a 66 MHz PCI bus, it reduces the speed of the PCI bus to 33 MHz.
As a result, you will receive superior performance with the 33 MHz UL3D, because it is tuned for a 33 MHz PCI bus.